Facebook

WELCOME TO OUR BLOG

We're sharing knowledge in the areas which fascinate us the most
click

Donor and Server Antenna Distance in Indoor Repeater Installation

By greetwin November 16th, 2026 7 views

Introduction: Antenna spacing in an indoor repeater sets how much amplified signal leaks back into the amplifier, and that leakage is what separates a stable system from one that keeps dropping out.

An installation learner sets up a five-band repeater, the signal looks good for a while, then calls break up, data stalls, and the unit shows a red alarm. The booster itself is often fine. On many sites the donor antenna and the server antenna simply sit too close together, so part of the amplified indoor signal travels back into the donor side and the repeater starts fighting its own output. this guide explains how distance, isolation, gain and self-oscillation connect, and why the manual gain control built into the unit and the physical layout of the site both matter.

What Donor and Server Antennas Do in an Indoor Repeater System

Every indoor repeater installation is built around two antennas doing opposite jobs. The donor antenna faces the outdoor base station and collects the weak signal that still reaches the building. The server antenna sits inside and spreads the amplified signal across rooms, corridors or floors. One antenna listens, the other speaks, and the repeater in the middle links them through its 50 ohm N-Female ports on both the uplink and downlink paths. That tidy picture hides a loop. The server antenna radiates into the building, and a fraction of that energy finds its way back to the donor antenna through open doorways, windows, corridors, reflections off metal surfaces, or even the wall between two rooms. The repeater cannot tell the difference between a weak signal from the tower and its own amplified signal arriving from behind. When the returning energy gets strong enough, the amplifier keeps re-amplifying itself, and the output becomes unstable. Insufficient isolation is the usual root cause, and antenna position is the main lever an installer has.

How Isolation Relates to Gain and Oscillation

Isolation is the attenuation between the two antennas, expressed in decibels. Gain is what the repeater adds. A cellular signal booster with 70dB±2dB uplink gain and 75dB±2dB downlink gain amplifies a very small input into a much larger output, so the isolation has to sit comfortably above the gain value. When the loop gain reaches unity and the phase lines up, the system meets the classic Barkhausen condition for oscillation: it becomes a transmitter of its own noise instead of a clean repeater. That relationship explains why distance matters far more than most beginners expect, and also why it cannot be reduced to a single figure. Isolation has to beat gain with margin, and both numbers shift with antenna type, mounting height, building materials and the direction each antenna points.

1. Distance Reduces Coupling, and No Single Meter Rule Fits Every Site

The Friis transmission formula describes how power falls off between two antennas as distance grows, and it also shows that antenna gain and frequency enter the calculation. In practice the indoor case is messier than free space: walls, floors, metal studs, glass and furniture all add attenuation, while a corridor can act like a pipe that carries signal around a corner. That is why copying a fixed meter figure from another project is risky. Two antennas ten meters apart in an open stairwell can couple more tightly than two antennas five meters apart on opposite sides of a concrete wall, especially if a high-gain directional panel points straight at the donor antenna. Installers get further by thinking in terms of attenuation budget: mount the donor antenna on the outside face of the building, point the server antenna away from it, use different floors or separate rooms where possible, and then verify the result on site.

2. Manual Gain Control Helps When Physical Separation Is Limited

Some buildings simply do not offer much separation. A small shop, a basement room, or a site where the outdoor antenna must sit close to the indoor one leaves the installer with less isolation than the gain wants. Manual gain control is the tool for that situation. The MGC on the Greetwin 20dBm five-band booster covers a 31dB adjustment range in 1dB steps, so the output can be trimmed precisely rather than in rough jumps. The practical sequence is straightforward. Run the system, watch the alarm LED, and reduce gain step by step until the red self-oscillation state clears and the green state holds, then leave a few dB of margin so a door opening or a moved shelf does not push it back over the edge. MGC is an auxiliary control rather than a replacement for physical separation: if the layout is poor enough, gain has to be cut so far that indoor coverage suffers.

Why Unstable Signals Should Be Read Through the Whole RF Path

A fluctuating signal is easy to blame on the booster, and that is usually the wrong first move. The RF path runs from the outdoor base station through the donor antenna, the feeder cable, the repeater, the second cable and the server antenna to the handset. Any weak link produces the same symptom. A donor signal that already hovers near the noise floor will deliver an unstable result no matter how carefully the indoor side is built, and a loose connector or a damaged cable adds loss and reflections that look like instability too. The alarm LEDs are the fastest way to narrow the field. A red alarm points to self-oscillation or a strong input signal, which sends the installer back to antenna separation and gain settings. A green alarm with a still-unstable signal points outward, toward donor signal quality, cable condition and connector fit. The LCD screen adds a second layer of status information during that check. Read in that order, the diagnosis becomes a short list: outdoor signal first, then antenna positions and isolation, then gain settings. Replacing hardware before walking that path usually costs money without solving anything, because the loop that caused the problem is still there in the building.

Conclusion

Donor and server antenna distance is really an isolation question, and isolation only makes sense next to gain. A repeater with 70dB to 75dB of gain needs far more separation than a low-gain unit, and how much separation a given site can deliver depends on walls, floors, antenna direction and building layout rather than a number copied from a manual. Physical placement does the heavy lifting, manual gain control cleans up the marginal cases, and the alarm LEDs tell an installer which of the two needs attention. Anyone planning a real installation can review the Greetwin 20dBm five-band booster page for its full frequency ranges, the 31dB MGC range and the alarm behavior before choosing antenna positions.

FAQ

Q: How close can donor and server antennas be in an indoor repeater installation?

A: There is no universal distance that fits every building, because what matters is the isolation between the two antennas rather than the gap in meters. A workable starting point is to put as much structure between them as the site allows — outside wall versus inside room, different floors, or opposite ends of the building — and to aim the server antenna away from the donor antenna. Then run the repeater and check the alarm state. If the red alarm appears, the isolation is below what the current gain needs, and either the layout or the gain setting has to change.

Q: Why do antennas need isolation if the booster has automatic level control?

A: Automatic level control protects the amplifier from excessive input and output by reducing gain when levels climb, which also limits interference toward the base station. It works on signal level at the amplifier, though, not on the physical path between the antennas. Once the server antenna couples enough energy back into the donor antenna, the loop closes regardless of what the level control does, because the returning signal keeps arriving. ALC handles overload; antenna isolation handles the feedback loop. The two solve different problems and neither replaces the other.

Q: Can manual gain control fix unstable signals caused by poor antenna separation?

A: It can stabilize many marginal installations. With a 31dB range in 1dB steps, an installer can walk the gain down until the red alarm clears, then back off a few dB more for margin. What it cannot do is create isolation that the building does not provide. On a site with very tight separation, the gain needed for stability may be so low that indoor coverage becomes too small to be useful, and the real fix is moving an antenna, adding a wall between the two, or re-aiming the server antenna.

Sources / References

Friis Equation - (aka Friis Transmission Formula)

Barkhausen Stability Criterion and Oscillation - TI

Related Examples

Greetwin 20dBm 5-Band 2G 3G 4G Signal Booster with LCD Screen, ALC&MGC Function

Previous
Custom Five-Band Signal Boosters for Distributor Projects
Read More